Liber Pigmenta Liber Pigmenta

Poradniki malowania / Warhammer 40,000 / Ultramarines / Intercessor Squad

Jak malować Intercessor Squad

Zdjęcia referencyjne, schematy kolorystyczne z dokładnymi farbami do każdego obszaru i gotowe modele innych malarzy — wszystko, czego potrzebujesz, żeby zacząć Intercessor Squad dla swojej armii Ultramarines.

Rola BattlelinePunkty 80Frakcja UltramarinesSystem Warhammer 40,000

InfantryGrenadesImperiumTacticusIntercessor Squad

Znajdź farbę

Każda farba poniżej prowadzi do jej odpowiedników w innych markach.

Jak wygląda Intercessor Squad

Zdjęcie referencyjne Intercessor Squad

Schematy kolorystyczne

Ultramarines — Intercessor Squad

Początkujący · 6 obszarów

The squad most painters start with, and the one that sets the standard for everything after it. Batch-paint the five as one model. Painted in Ultramarines colours, from primer to based.

Power armour

  1. Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
  2. Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
  3. Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

  1. Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
  2. Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
  3. Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of gold on the ammo feed.

Shoulder trim and gold

  1. Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
  2. Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
  3. Highlight the trim Edge highlight

Helmet lenses

  1. Fill the lens Basecoat — Fill the whole lens recess with the darkest red.
  2. Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
  3. Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Chapter markings

  1. Block in the right shoulder pad Basecoat — Ultramarines wear a bone pad on the right shoulder. Two thin coats beat one thick one over blue.
  2. Shade and clean up Recess shade — A pin-wash into the pad rim only — flooding the whole pad turns bone into mud.
  3. Highlight the pad and paint the chapter symbol Edge highlight — Screaming Skull on the upper edge, then the omega symbol freehand or transfer.

Base

  1. Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
  2. Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
  3. Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Wszystkie farby na tej stronie

19 farb we wszystkich schematach i poradnikach powyżej. Odhacz to, czego potrzebujesz, żeby zbudować listę, albo przejdź do farby, żeby znaleźć ją w innej marce.

Więcej poradników malowania Ultramarines →

Prowadź ten projekt od ramki do gotowego modelu

Dodaj Intercessor Squad do stosu, odhacz farby, które już masz, i sprawdź, czego jeszcze brakuje, zanim otworzysz pudełko.

Dodaj do stosu — bez konta

Wygeneruj schemat kolorów — bez konta

Farby na Twojej liście: 0 Zapisz tę listę