Liber Pigmenta Liber Pigmenta

Malanleitungen / Warhammer 40,000 / Ultramarines / Intercessor Squad

Intercessor Squad bemalen

Referenzfotos, Farbschemata mit den genauen Farben für jeden Bereich und fertige Modelle anderer Maler — alles, was du brauchst, um Intercessor Squad für deine Ultramarines zu beginnen.

Rolle BattlelinePunkte 80Fraktion UltramarinesSystem Warhammer 40,000

InfantryGrenadesImperiumTacticusIntercessor Squad

Eine Farbe finden

Jede Farbe unten verlinkt auf ihre Entsprechungen in anderen Marken.

So sieht Intercessor Squad aus

Referenzfoto von Intercessor Squad

Farbschemata

Ultramarines — Intercessor Squad

Anfänger · 6 Bereiche

The squad most painters start with, and the one that sets the standard for everything after it. Batch-paint the five as one model. Painted in Ultramarines colours, from primer to based.

Power armour

  1. Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
  2. Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
  3. Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

  1. Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
  2. Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
  3. Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of gold on the ammo feed.

Shoulder trim and gold

  1. Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
  2. Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
  3. Highlight the trim Edge highlight

Helmet lenses

  1. Fill the lens Basecoat — Fill the whole lens recess with the darkest red.
  2. Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
  3. Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Chapter markings

  1. Block in the right shoulder pad Basecoat — Ultramarines wear a bone pad on the right shoulder. Two thin coats beat one thick one over blue.
  2. Shade and clean up Recess shade — A pin-wash into the pad rim only — flooding the whole pad turns bone into mud.
  3. Highlight the pad and paint the chapter symbol Edge highlight — Screaming Skull on the upper edge, then the omega symbol freehand or transfer.

Base

  1. Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
  2. Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
  3. Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Alle Farben auf dieser Seite

19 Farben über alle Farbschemata und Tutorials oben. Hake ab, was du brauchst, um eine Liste aufzubauen, oder folge einer Farbe, um sie in einer anderen Marke zu finden.

Mehr Malanleitungen für Ultramarines →

Begleite dieses Projekt vom Spritzling bis fertig

Lege Intercessor Squad auf deinen Stapel, hake die Farben ab, die du schon hast, und sieh, was noch fehlt, bevor du die Box öffnest.

Auf den Stapel legen — ohne Konto

Farbschema generieren — ohne Konto

0 Farben auf deiner Liste Liste speichern