Liber Pigmenta Liber Pigmenta

Guías de pintado / Warhammer 40,000 / Dark Angels / Intercessor Squad

Cómo pintar Intercessor Squad

Fotos de referencia, esquemas de color con las pinturas exactas de cada zona y miniaturas acabadas de otros pintores — todo lo que necesitas para empezar Intercessor Squad para tu fuerza de Dark Angels.

Rol BattlelinePuntos 80Facción Dark AngelsSistema Warhammer 40,000

InfantryGrenadesImperiumTacticusIntercessor Squad

Buscar una pintura

Cada pintura de abajo enlaza con sus equivalentes en otras marcas.

Qué aspecto tiene Intercessor Squad

Foto de referencia de Intercessor Squad

Esquemas de color

Dark Angels — Intercessor Squad

Principiante · 6 zonas

The squad most painters start with, and the one that sets the standard for everything after it. Batch-paint the five as one model. Painted in Dark Angels colours, from primer to based.

Power armour

  1. Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
  2. Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
  3. Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

  1. Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
  2. Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
  3. Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of bronze on the ammo feed.

Shoulder trim and bronze

  1. Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
  2. Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
  3. Highlight the trim Edge highlight

Helmet lenses

  1. Fill the lens Basecoat — Fill the whole lens recess with the darkest red.
  2. Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
  3. Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Bone robes and tabards

  1. Basecoat the robes Basecoat — Ushabti Bone over a grey primer covers in two coats; over black it will take four.
  2. Shade the folds All-over shade — Seraphim Sepia across the whole robe — cloth is one of the few areas that wants a full shade, not a pin-wash.
  3. Highlight the raised folds Drybrush — A light drybrush of Screaming Skull picks out the fold ridges without redrawing them.

Base

  1. Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
  2. Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
  3. Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Todas las pinturas de esta página

19 pinturas entre todos los esquemas y tutoriales de arriba. Marca lo que necesites para armar una lista, o sigue una pintura para encontrarla en otra marca.

Más guías de pintado de Dark Angels →

Sigue este proyecto desde la bancada hasta el final

Añade Intercessor Squad a tu pila, marca las pinturas que ya tienes y comprueba qué falta antes de abrir la caja.

Añádelo a tu pila — sin cuenta

Genera un esquema de color — sin cuenta

0 pinturas en tu lista Guardar esta lista