Референсні фото, колірні схеми з точними фарбами для кожної зони та готові моделі інших малярів — усе, що потрібно, щоб узятися за Terminator Squad для вашого війська Salamanders.

Роль InfantryОчки 160Фракція SalamandersСистема Warhammer 40,000

Знайти фарбу

Кожна фарба нижче веде до її відповідників в інших брендах.

Як виглядає Terminator Squad

Колірні схеми

Salamanders — Terminator Squad

Середній · 7 зон

Bigger plates, more bare metal and more room for weathering than a battleline squad — a good second project once the armour recipe is habit. Painted in Salamanders colours, from primer to based.

Power armour

Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

Leadbelcher Citadel
Nuln Oil Citadel
Ironbreaker Citadel

Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of steel on the ammo feed.

Shoulder trim and steel

Leadbelcher Citadel
Nuln Oil Citadel
Ironbreaker Citadel

Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
Highlight the trim Edge highlight

Helmet lenses

Fill the lens Basecoat — Fill the whole lens recess with the darkest amber.
Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Terminator plate and hazard stripes

Pick out the storm bolter and power fist Layer — Terminator armour carries far more bare metal than a battleline marine — shade it harder so the bulk reads.
Hazard stripes on the fist Detail — Averland Sunset field, then thin black diagonals. Mark the stripe spacing in pencil first.
Weathering on the boots and skirt Stipple — Stipple Typhus Corrosion low on the legs, then a light Ryza Rust catch on the rivets.

Coal-black skin and flame weapons

Basecoat exposed skin Basecoat — Salamanders have jet-black skin and burning red eyes — the single most recognisable thing about the chapter.
Build the skin back up Layer — Eshin Grey on the brow, nose and cheekbones, then a sparing Dawnstone on the highest points only.
Eyes and flamer nozzles Detail — Troll Slayer Orange eyes; scorch the flamer nozzle with Typhus Corrosion then a Ryza Rust drybrush.

Base

Astrogranite Citadel
Administratum Grey Citadel
Dawnstone Citadel
Abaddon Black Citadel

Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Усі фарби на цій сторінці

18 фарб по всіх схемах і туторіалах вище. Позначте те, що вам потрібно, щоб скласти список, або перейдіть до фарби, щоб знайти її в іншому бренді.

Ведіть цей проєкт від литника до готової моделі

Додайте Terminator Squad до своєї купи, позначте фарби, які у вас уже є, і подивіться, чого ще бракує, перш ніж відкривати коробку.

Додати до купи — без акаунта

Згенерувати кольорову схему — без акаунта