Zdjęcia referencyjne, schematy kolorystyczne z dokładnymi farbami do każdego obszaru i gotowe modele innych malarzy — wszystko, czego potrzebujesz, żeby zacząć Redemptor Dreadnought dla swojej armii Imperial Fists.

Znajdź farbę

Każda farba poniżej prowadzi do jej odpowiedników w innych markach.

Jak wygląda Redemptor Dreadnought

Zdjęcie referencyjne Redemptor Dreadnought

Pokazuje serię Imperial Fists, a nie konkretnie Redemptor Dreadnought — to samo zdjęcie reprezentuje 8 jednostek tej armii.

Schematy kolorystyczne

Imperial Fists — Redemptor Dreadnought

Średni · 6 obszarów

A vehicle wearing chapter colours. The recipe is the same; the surfaces are flat, large and unforgiving, so the technique changes. Painted in Imperial Fists colours, from primer to based.

Power armour

Undercoat light Primer — Yellow has almost no covering power over black. Starting from a bone primer is the difference between two coats and six.
Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.
Sharpen the brightest edges Edge highlight — Only the corners and the very top of each plate — this is a fraction of the previous line.

Shoulder trim and steel

Leadbelcher Citadel
Nuln Oil Citadel
Ironbreaker Citadel

Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
Highlight the trim Edge highlight

Helmet lenses

Caliban Green Citadel
Warpstone Glow Citadel
Moot Green Citadel
White Scar Citadel

Fill the lens Basecoat — Fill the whole lens recess with the darkest green.
Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Hull panels and sarcophagus

Basecoat the large panels Basecoat — Large flat panels show brush marks a shoulder pad hides. Thin further than you would for infantry and build up three coats.
Panel-line the hull Recess shade — Nuln Oil drawn along the panel gaps with the tip of the brush, not washed across the panel.
Sarcophagus and ironwork Layer — The sarcophagus face and its steel surround are the focal point — spend the time here, not on the shins.
Chipping along the leading edges Stipple — Sponge Rhinox Hide chips first, then a smaller Leadbelcher chip inside some of them.

Black plates and chapter badge

Basecoat the black plates Basecoat — Imperial Fists break up the yellow with black knee and shoulder plates — paint these before the final yellow highlight so overspill is easy to fix.
Edge the black Edge highlight — A single Eshin Grey line; anything brighter fights the yellow for attention.
Paint the fist Layer — Mephiston Red field with a Flash Gitz Yellow fist, or a transfer over gloss varnish.

Base

Astrogranite Citadel
Administratum Grey Citadel
Dawnstone Citadel
Abaddon Black Citadel

Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Wszystkie farby na tej stronie

19 farb we wszystkich schematach i poradnikach powyżej. Odhacz to, czego potrzebujesz, żeby zbudować listę, albo przejdź do farby, żeby znaleźć ją w innej marce.

Prowadź ten projekt od ramki do gotowego modelu

Dodaj Redemptor Dreadnought do stosu, odhacz farby, które już masz, i sprawdź, czego jeszcze brakuje, zanim otworzysz pudełko.

Dodaj do stosu — bez konta

Wygeneruj schemat kolorów — bez konta