Zdjęcia referencyjne, schematy kolorystyczne z dokładnymi farbami do każdego obszaru i gotowe modele innych malarzy — wszystko, czego potrzebujesz, żeby zacząć Assault Intercessor Squad dla swojej armii Dark Angels.

Znajdź farbę

Każda farba poniżej prowadzi do jej odpowiedników w innych markach.

Jak wygląda Assault Intercessor Squad

Schematy kolorystyczne

Dark Angels — Assault Intercessor Squad

Początkujący · 7 obszarów

Same armour recipe as the Intercessors, with chainsword teeth and a plasma pistol to break up the silhouette. Painted in Dark Angels colours, from primer to based.

Power armour

Caliban Green Citadel
Nuln Oil Citadel
Warpstone Glow Citadel

Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

Leadbelcher Citadel
Nuln Oil Citadel
Ironbreaker Citadel
Balthasar Gold Citadel

Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of bronze on the ammo feed.

Shoulder trim and bronze

Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
Highlight the trim Edge highlight

Helmet lenses

Fill the lens Basecoat — Fill the whole lens recess with the darkest red.
Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Chainsword and plasma

Chainsword housing and teeth Layer — Leadbelcher teeth over an Abaddon Black housing, then Nuln Oil to knock the shine back.
Bare metal on the cutting edge Drybrush — A light Runefang Steel drybrush across the teeth only — this is where the eye lands.
Plasma coil glow Glaze — Blue Horror over the coil, White Scar in the centre, then a Tesseract Glow glaze to tie it together.

Bone robes and tabards

Basecoat the robes Basecoat — Ushabti Bone over a grey primer covers in two coats; over black it will take four.
Shade the folds All-over shade — Seraphim Sepia across the whole robe — cloth is one of the few areas that wants a full shade, not a pin-wash.
Highlight the raised folds Drybrush — A light drybrush of Screaming Skull picks out the fold ridges without redrawing them.

Base

Astrogranite Citadel
Administratum Grey Citadel
Dawnstone Citadel
Abaddon Black Citadel

Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Wszystkie farby na tej stronie

22 farby we wszystkich schematach i poradnikach powyżej. Odhacz to, czego potrzebujesz, żeby zbudować listę, albo przejdź do farby, żeby znaleźć ją w innej marce.

Prowadź ten projekt od ramki do gotowego modelu

Dodaj Assault Intercessor Squad do stosu, odhacz farby, które już masz, i sprawdź, czego jeszcze brakuje, zanim otworzysz pudełko.

Dodaj do stosu — bez konta

Wygeneruj schemat kolorów — bez konta