Liber Pigmenta Liber Pigmenta

Poradniki malowania / Warhammer 40,000 / Blood Angels / Intercessor Squad

Jak malować Intercessor Squad

Zdjęcia referencyjne, schematy kolorystyczne z dokładnymi farbami do każdego obszaru i gotowe modele innych malarzy — wszystko, czego potrzebujesz, żeby zacząć Intercessor Squad dla swojej armii Blood Angels.

Rola BattlelinePunkty 80Frakcja Blood AngelsSystem Warhammer 40,000

InfantryGrenadesImperiumTacticusIntercessor Squad

Znajdź farbę

Każda farba poniżej prowadzi do jej odpowiedników w innych markach.

Jak wygląda Intercessor Squad

Zdjęcie referencyjne Intercessor Squad

Schematy kolorystyczne

Blood Angels — Intercessor Squad

Początkujący · 6 obszarów

The squad most painters start with, and the one that sets the standard for everything after it. Batch-paint the five as one model. Painted in Blood Angels colours, from primer to based.

Power armour

  1. Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
  2. Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
  3. Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.
  4. Sharpen the brightest edges Edge highlight — Only the corners and the very top of each plate — this is a fraction of the previous line.

Bolter and metal

  1. Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
  2. Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
  3. Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of gold on the ammo feed.

Shoulder trim and gold

  1. Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
  2. Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
  3. Highlight the trim Edge highlight

Helmet lenses

  1. Fill the lens Basecoat — Fill the whole lens recess with the darkest green.
  2. Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
  3. Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Black weapon casings and seals

  1. Basecoat the casings Basecoat — Bolter casings and backpack vents stay black — the contrast is what stops the model reading as one flat red shape.
  2. Raise the edges out of the black Edge highlight — Eshin Grey first, then a thinner Dawnstone line on the sharpest edges only.
  3. Purity seals Layer — Ushabti Bone parchment, Seraphim Sepia into the folds, Mephiston Red wax blob.

Base

  1. Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
  2. Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
  3. Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Wszystkie farby na tej stronie

21 farb we wszystkich schematach i poradnikach powyżej. Odhacz to, czego potrzebujesz, żeby zbudować listę, albo przejdź do farby, żeby znaleźć ją w innej marce.

Więcej poradników malowania Blood Angels →

Prowadź ten projekt od ramki do gotowego modelu

Dodaj Intercessor Squad do stosu, odhacz farby, które już masz, i sprawdź, czego jeszcze brakuje, zanim otworzysz pudełko.

Dodaj do stosu — bez konta

Wygeneruj schemat kolorów — bez konta

Farby na Twojej liście: 0 Zapisz tę listę