Fotos de referencia, esquemas de color con las pinturas exactas de cada zona y miniaturas acabadas de otros pintores — todo lo que necesitas para empezar Terminator Squad para tu fuerza de Ultramarines.

Buscar una pintura

Cada pintura de abajo enlaza con sus equivalentes en otras marcas.

Qué aspecto tiene Terminator Squad

Esquemas de color

Ultramarines — Terminator Squad

Intermedio · 7 zonas

Bigger plates, more bare metal and more room for weathering than a battleline squad — a good second project once the armour recipe is habit. Painted in Ultramarines colours, from primer to based.

Power armour

Macragge Blue Citadel
Nuln Oil Citadel
Calgar Blue Citadel

Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.

Bolter and metal

Leadbelcher Citadel
Nuln Oil Citadel
Ironbreaker Citadel
Retributor Armour Citadel

Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of gold on the ammo feed.

Shoulder trim and gold

Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
Highlight the trim Edge highlight

Helmet lenses

Fill the lens Basecoat — Fill the whole lens recess with the darkest red.
Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Terminator plate and hazard stripes

Pick out the storm bolter and power fist Layer — Terminator armour carries far more bare metal than a battleline marine — shade it harder so the bulk reads.
Hazard stripes on the fist Detail — Averland Sunset field, then thin black diagonals. Mark the stripe spacing in pencil first.
Weathering on the boots and skirt Stipple — Stipple Typhus Corrosion low on the legs, then a light Ryza Rust catch on the rivets.

Chapter markings

Ushabti Bone Citadel
Seraphim Sepia Citadel
Screaming Skull Citadel
White Scar Citadel

Block in the right shoulder pad Basecoat — Ultramarines wear a bone pad on the right shoulder. Two thin coats beat one thick one over blue.
Shade and clean up Recess shade — A pin-wash into the pad rim only — flooding the whole pad turns bone into mud.
Highlight the pad and paint the chapter symbol Edge highlight — Screaming Skull on the upper edge, then the omega symbol freehand or transfer.

Base

Astrogranite Citadel
Administratum Grey Citadel
Dawnstone Citadel
Abaddon Black Citadel

Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Todas las pinturas de esta página

22 pinturas entre todos los esquemas y tutoriales de arriba. Marca lo que necesites para armar una lista, o sigue una pintura para encontrarla en otra marca.

Sigue este proyecto desde la bancada hasta el final

Añade Terminator Squad a tu pila, marca las pinturas que ya tienes y comprueba qué falta antes de abrir la caja.

Añádelo a tu pila — sin cuenta

Genera un esquema de color — sin cuenta