Guías de pintado / Warhammer 40,000 / Blood Angels / Terminator Squad
Cómo pintar Terminator Squad
Fotos de referencia, esquemas de color con las pinturas exactas de cada zona y miniaturas acabadas de otros pintores — todo lo que necesitas para empezar Terminator Squad para tu fuerza de Blood Angels.
Rol InfantryPuntos 160Facción Blood AngelsSistema Warhammer 40,000
ImperiumTerminatorTerminator Squad
Cada pintura de abajo enlaza con sus equivalentes en otras marcas.
Qué aspecto tiene Terminator Squad
Esquemas de color
Blood Angels — Terminator Squad
Bigger plates, more bare metal and more room for weathering than a battleline squad — a good second project once the armour recipe is habit. Painted in Blood Angels colours, from primer to based.
Power armour
- Mephiston Red Citadel
- Carroburg Crimson Citadel
- Evil Sunz Scarlet Citadel
- Wild Rider Red Citadel
- Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
- Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
- Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.
- Sharpen the brightest edges Edge highlight — Only the corners and the very top of each plate — this is a fraction of the previous line.
Bolter and metal
- Leadbelcher Citadel
- Nuln Oil Citadel
- Ironbreaker Citadel
- Retributor Armour Citadel
- Basecoat the metal Basecoat — Leadbelcher over the bolter body, barrel and any exposed pistons.
- Shade the metal All-over shade — Nuln Oil across the whole weapon — metallics are the one area that wants a full wash.
- Bring back the edges Edge highlight — Ironbreaker on the barrel rim and casing edges, then a spot of gold on the ammo feed.
Shoulder trim and gold
- Retributor Armour Citadel
- Agrax Earthshade Citadel
- Auric Armour Gold Citadel
- Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
- Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
- Highlight the trim Edge highlight
Helmet lenses
- Caliban Green Citadel
- Warpstone Glow Citadel
- Moot Green Citadel
- White Scar Citadel
- Fill the lens Basecoat — Fill the whole lens recess with the darkest green.
- Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
- Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.
Terminator plate and hazard stripes
- Leadbelcher Citadel
- Nuln Oil Citadel
- Averland Sunset Citadel
- Abaddon Black Citadel
- Typhus Corrosion Citadel
- Ryza Rust Citadel
- Pick out the storm bolter and power fist Layer — Terminator armour carries far more bare metal than a battleline marine — shade it harder so the bulk reads.
- Hazard stripes on the fist Detail — Averland Sunset field, then thin black diagonals. Mark the stripe spacing in pencil first.
- Weathering on the boots and skirt Stipple — Stipple Typhus Corrosion low on the legs, then a light Ryza Rust catch on the rivets.
Black weapon casings and seals
- Abaddon Black Citadel
- Eshin Grey Citadel
- Dawnstone Citadel
- Ushabti Bone Citadel
- Seraphim Sepia Citadel
- Mephiston Red Citadel
- Basecoat the casings Basecoat — Bolter casings and backpack vents stay black — the contrast is what stops the model reading as one flat red shape.
- Raise the edges out of the black Edge highlight — Eshin Grey first, then a thinner Dawnstone line on the sharpest edges only.
- Purity seals Layer — Ushabti Bone parchment, Seraphim Sepia into the folds, Mephiston Red wax blob.
Base
- Astrogranite Citadel
- Administratum Grey Citadel
- Dawnstone Citadel
- Abaddon Black Citadel
- Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
- Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
- Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.
Todas las pinturas de esta página
24 pinturas entre todos los esquemas y tutoriales de arriba. Marca lo que necesites para armar una lista, o sigue una pintura para encontrarla en otra marca.
- Abaddon Black Citadel
- Administratum Grey Citadel
- Agrax Earthshade Citadel
- Astrogranite Citadel
- Auric Armour Gold Citadel
- Averland Sunset Citadel
- Caliban Green Citadel
- Carroburg Crimson Citadel
- Dawnstone Citadel
- Eshin Grey Citadel
- Evil Sunz Scarlet Citadel
- Ironbreaker Citadel
- Leadbelcher Citadel
- Mephiston Red Citadel
- Moot Green Citadel
- Nuln Oil Citadel
- Retributor Armour Citadel
- Ryza Rust Citadel
- Seraphim Sepia Citadel
- Typhus Corrosion Citadel
- Ushabti Bone Citadel
- Warpstone Glow Citadel
- White Scar Citadel
- Wild Rider Red Citadel
Más guías de pintado de Blood Angels →
Sigue este proyecto desde la bancada hasta el final
Añade Terminator Squad a tu pila, marca las pinturas que ya tienes y comprueba qué falta antes de abrir la caja.







