Referenzfotos, Farbschemata mit den genauen Farben für jeden Bereich und fertige Modelle anderer Maler — alles, was du brauchst, um Redemptor Dreadnought für deine Blood Angels zu beginnen.

Eine Farbe finden

Jede Farbe unten verlinkt auf ihre Entsprechungen in anderen Marken.

So sieht Redemptor Dreadnought aus

Zeigt die Reihe Blood Angels und nicht Redemptor Dreadnought im Besonderen — dasselbe Bild steht für 7 Einheiten dieser Armee.

Farbschemata

Blood Angels — Redemptor Dreadnought

Mittel · 6 Bereiche

A vehicle wearing chapter colours. The recipe is the same; the surfaces are flat, large and unforgiving, so the technique changes. Painted in Blood Angels colours, from primer to based.

Power armour

Basecoat the armour plates Basecoat — Two thin coats, leaving the recesses slightly darker. Thin with water until the paint flows off the brush rather than sits on it.
Shade the recesses Recess shade — Run the shade into panel lines and around raised details only. A full wash over the plates flattens the armour.
Edge highlight the plates Edge highlight — A fine line along the top edge of each plate, where light would land. Stop before the line meets the next edge.
Sharpen the brightest edges Edge highlight — Only the corners and the very top of each plate — this is a fraction of the previous line.

Shoulder trim and gold

Basecoat the trim Basecoat — Keep the line clean — trim is what the eye follows, so a wobble here is more visible than one anywhere else.
Shade the trim Recess shade — Agrax Earthshade where the trim meets the plate, so it reads as a separate piece of metal.
Highlight the trim Edge highlight

Helmet lenses

Caliban Green Citadel
Warpstone Glow Citadel
Moot Green Citadel
White Scar Citadel

Fill the lens Basecoat — Fill the whole lens recess with the darkest green.
Leave a dark rim Layer — Cover the lens again but stop short of the bottom edge, leaving a crescent of the base colour.
Dot the catchlight Detail — One small dot in the upper corner. The dot is what makes the lens read as glass.

Hull panels and sarcophagus

Basecoat the large panels Basecoat — Large flat panels show brush marks a shoulder pad hides. Thin further than you would for infantry and build up three coats.
Panel-line the hull Recess shade — Nuln Oil drawn along the panel gaps with the tip of the brush, not washed across the panel.
Sarcophagus and ironwork Layer — The sarcophagus face and its gold surround are the focal point — spend the time here, not on the shins.
Chipping along the leading edges Stipple — Sponge Rhinox Hide chips first, then a smaller Leadbelcher chip inside some of them.

Black weapon casings and seals

Basecoat the casings Basecoat — Bolter casings and backpack vents stay black — the contrast is what stops the model reading as one flat red shape.
Raise the edges out of the black Edge highlight — Eshin Grey first, then a thinner Dawnstone line on the sharpest edges only.
Purity seals Layer — Ushabti Bone parchment, Seraphim Sepia into the folds, Mephiston Red wax blob.

Base

Astrogranite Citadel
Administratum Grey Citadel
Dawnstone Citadel
Abaddon Black Citadel

Texture the base Texture — Astrogranite straight from the pot with an old brush, kept off the rim.
Drybrush the rubble Drybrush — Administratum Grey, then a lighter pass so only the highest grit catches it.
Paint the rim Detail — Abaddon Black around the rim in one steady pass. A clean rim is what makes a squad look finished.

Alle Farben auf dieser Seite

21 Farben über alle Farbschemata und Tutorials oben. Hake ab, was du brauchst, um eine Liste aufzubauen, oder folge einer Farbe, um sie in einer anderen Marke zu finden.

Begleite dieses Projekt vom Spritzling bis fertig

Lege Redemptor Dreadnought auf deinen Stapel, hake die Farben ab, die du schon hast, und sieh, was noch fehlt, bevor du die Box öffnest.

Auf den Stapel legen — ohne Konto

Farbschema generieren — ohne Konto